Tagged With "wireless"

Topic

Preset tonematch setting for Shure BLX288/PG58 Wireless mics

sri ·
Team , I just purchased Shure PG58 wireless mics. My current setup is L1M2 B2 with T8S. I am currently using tonematch setting of "Handheld Mic" for the new PG58. is there a preset which is compatible with this mic. I am hoping there should be a better setting to take advantage of this 600$ mics. Pls help. Mics are used for vocal singing ...
Topic

Wireless Lavelier Mics & S1 Pro | Very Low Output!

KC ·
Greetings! We are Theatre/Storytelling collective, and require amplification support for our solo (speech only) performances. We own a Saramonic UHF Wireless Lavalier Mic System UwMic9 for video recording. These are the specs: Audio output level -60dBV (mic level) Headphone output level : 30mw (16 ohm) Sensitivity: -95dBm Signal to noise ratio : 70 dB or more Voice delay: 12ms Frequency response: 40kz to 18kHz Distortion: 0.5% or less Spur suppression: -60db We have used this in the past...
Topic

Wireless Shure SM58 settings?

Collie ·
I've got a wireless SM58 what's the best settings to have for excellent sound , I'm struggling to get one
Topic

Wireless transmitter/receiver to use with two S1 pro speakers

Harry 3 ·
Looking for recommendations or experience on using a wireless transmitter/receiver with two S1 pro speakers, hoping to use them for wedding ceremonys or remote fill speakers. A little worried about the reliability of wireless. Thanks!
Topic

Bluetooth transmitter solution - for T1 to S1 Pro

hoohaa1 ·
Looking to purchase an S1 Pro. I already have an L1 Model 2 that has really been a game changer for me the last few years. What I'm looking for advice on is a way to extend the coverage of my L1 on occasions wirelessly to the S1 Pro. I can obviously do this with a cable, but seeing as the S1 Pro has bluetooth - can anyone recommend a simple solution that I can connect the master from my T1 tonematch to transmit the same signal to the S1 Pro - say at the other end of room for coverage? I've...
Topic

Connect Bose Wireless Speakers to L1 Model II

Gordo ·
I wonder if I connect a T4S "Out (L/R)" to the wireless link "Aux In" then use the Sound Touch App to configure Bose speakers on the wireless WIFI link (not bluetooth) if this would enable remote wireless speaker capability from the L1 model SII. See below. Thanks - Gordon
Topic

Wireless Mics on L1 Model II

Gordo ·
Can I attach wireless mics to my L1 Model II through the T4S Tonematch? If Yes... what would you recommend? Thanks
Topic

Sound Touch Wireless Link Adapter

Gordo ·
Can I add the Sound Touch Wireless Link Adapter and related speaker(s) to my Bose L1 Model II system for additional wireless speaker capability? Thanks Gordon
Topic

Wireless transmitters

zipster048 ·
Hi, I have a Bose T1 Tonematch system and I want to have the ability to mix wirelessly. Am I able to do this and if so what are some some suggestions to wireless transmitters or iPad apps that are compatible? edit subject: previously "Wireless tansmitters"
Topic

best wireless MICs for T8S and L1 M2

sri ·
New to this world. Bought my new L1 model 2 with T8S. wondering what is the best wireless MICs . also one which can adv of the T8S presets. Mics are mainly for singing only. thoughts on Shure BLX288/PG58 if anyone used it. Thanks
Reply

Re: wireless mic feedback

ST ·
Hi LowG, Thank you for joining the Forum. Is your Shure wireless microphone hand-held or something that you clip to your clothing or wear on your head? Here are some general tips for dealing with Microphone Feedback. Does that help? ST
Reply

Re: wireless mic feedback

hello it depends on capsule, You use. A Headset with almost 360° is more liable to feedbacks than a hyper-cardiodid Mic. May be a higher distance to the Array will reduce the feedbacks
Reply

Re: wireless mic feedback

Seagullman ·
Hi LowG, and a warm welcome to the forum from me, too. If you could give us more information regarding your system we may be able to give more precise advice/tips as to finding a way to reduce the feedback problem. Which Shure wireless microphone model are you using? This information will let us know which directionality (polar pattern) the microphone has (directionality means from which side/s the microphone actually hears sound. Omnidirectional means that it receives sound from all sides...
Reply

Re: wireless mic feedback

lowG ·
Thank you for the information. I just bought a Shure PGA31. I hope that will help. I've tried moving the L1C. It is really odd because it happens more with one presenter than others. I tried turning down the tone but it got very basey. Oh the mic in this case is only used for speaking. When I used a corded mic for singing -- no problems! Again, thank you for the information.
Reply

Re: wireless mic feedback

Seagullman ·
Hi LowG, thanks for the information regarding the microphone. Is this the one we're talking about? http://cdn.shure.com/specifica...cification_Sheet.pdf If so I've had a look at the specs for it. The polar pattern is cardioid (they say it's unidirectional but the cardioid pattern will probably not be able to reject enough of the signal from the loudspeaker to be feedback free when standing in front of it. Apollo Audio & Stage Services wrote: "it depends on capsule, You use. A Headset...
Reply

Re: wireless mic feedback

Lee Wright ·
Hi LowG, I run a hire company where we use the Compacts & L1 Model 2's a lot. Headsets are always a lot more feedback prone than hand helds & when you use then with a rear mounted speaker like the Compact you're looking for trouble. A couple of things I can suggest: -The Shure WH20 is the dynamic version of that type of headset. They're reasonably priced & a lot more feedback resistant. -We often use feedback eliminators like the DBX AFS224, AFS2 or DriveRack. Not everyone likes...
Reply

Re: wireless mic feedback

lowG ·
Thank you Lee. I'll look into the WH20
Reply

Re: wireless mic feedback

lowG ·
Thank you Tony. I will try your suggestions
Reply

Re: wireless mic feedback

ST ·
Hi lowg, I suggest that you try the Shure PGA31 since you've actually go it. I have one and I've used it for public speaking with a Compact many times. It was fine to stand in front of the Compact as long as I was aware that I should not turn around and look at the Compact while wearing it. The feedback occurred when I as I was turning toward it or walking close to the Compact. It was fine as long as my head was between the microphone and the Compact. I also have a Shure WH20. I got it after...
Reply

Re: wireless mic feedback

lowG ·
Thank you ST. I will keep your tips in mind.
Reply

Re: wireless mic feedback

Seagullman ·
Hi lowG , ST's advice: "I suggest that you try the Shure PGA31 since you've actually go it. I have one and I've used it for public speaking with a Compact many times. It was fine to stand in front of the Compact as long as I was aware that I should not turn around and look at the Compact while wearing it. The feedback occurred when I as I was turning toward it or walking close to the Compact. It was fine as long as my head was between the microphone and the Compact." is really good advice.
Reply

Re: Wireless transmitter/receiver to use with two S1 pro speakers

Daniel Proctor ·
I'd like input on this as well.
Reply

Re: Wireless transmitter/receiver to use with two S1 pro speakers

ST ·
We had some input in this discussion. What are you using for wireless connections between your Bose systems? ST
Reply

Re: Wireless transmitter/receiver to use with two S1 pro speakers

ST ·
Hi again, There are some considerations with the S1 Pro system because it is so portable. You may be looking for A battery powered receiver (the part that goes into the S1 Pro system input). A battery powered transmitter. If you want to replace the wire that you use to daisy chain two S1 Pro systems, the transmitter would take the signal from S1 Pro Line Out and transmit that to the receiver on the second S1 Pro system. Bluetooth is great for sending prerecorded music from a Bluetooth...
Reply

Re: Wireless transmitter/receiver to use with two S1 pro speakers

Harry 3 ·
Thanks for the info... more specifically looking for ideas to go from a mixer out to wireless transmitter to wireless receiver (battery powered) into Bose s1 pro. Alto stealth wireless for speakers is the type of system I'm thinking of, but recevers are not battery powered. Or, perhaps a Bluetooth transmitter that would connect to mixer out and then pair to the s1 pro Bluetooth. https://www.sweetwater.com/sto...tem-for-loudspeakers
Reply

Re: Wireless transmitter/receiver to use with two S1 pro speakers

MUSIKaage ·
Hi Harry Thanks for bringing this topic up. WIRELESS transmission. I play what we in Denmark call dinner music. Groups: up to 120 people. My setup is: Piano - Tone match4 - Compact L1 cabled - Wireless to second Compact L1. Currently I use a XVive U2 (which is made for instruments) between the first and second Compact L1. It works, but from time to time the quality is too poor because of too much electronic noise in the room I think. Wonder if anyone has any wireless transmission experience.
Reply

Re: Wireless transmitter/receiver to use with two S1 pro speakers

Scott Hanna ·
I use Sennheiser ew112-p G3. Wireless transmitter and receiver. Works perfectly
Reply

Re: Wireless transmitter/receiver to use with two S1 pro speakers

Harry 3 ·
Thread Update: Wireless Solution for Pair of S1 Pros... Ran a pair of S1 Pros in conjunction with the Xvive U3 Wireless Transmitter / Receiver pair last thursday 3/28/2019, setup as follows... Bose T1 Mixer main out (1/4" to 1/4" TRS cable) > > To: speaker 1 S1 Pro channel 1 input, settings = tonematch off, reverb off, bass and treble at 12:00, volume at 12:00 > Speaker 1 S1 Pro line out, Male TRS to Male XLR patch cable >To: Xvive U3 Transmitter (taped to back of speaker 1)...
Reply

Re: Wireless Lavelier Mics & S1 Pro | Very Low Output!

ST ·
Hi KC, Welcome to the Bose Portable PA Community. Let's check this in a couple of ways. Connect a wired microphone using an XLR cable to the S1 Pro Channel 1. You should be able to get a loud output with the volume control at 3:00 o'clock. You won't get much output below 12:00 o'clock. Looking at the specifications and the owners manual for the UwMic9 receiver it appears that the output is -6 dB lower than a Shure SM58 hand-held microphone. Based on that, I'd expect you would have turn up...
Reply

Re: Wireless Lavelier Mics & S1 Pro | Very Low Output!

KC ·
Dear ST, Thank you for your prompt response! I have connected the XLR out of the UWmic 9 receiver to both the inputs of the Bose SE pro. Even on close to full volume, the output is barely sufficient - it's close 15% of what it gives when used as a Bluetooth speaker. I haven't tried the 3.5 output into the Aux Input. Will try & get back. I have used the same XLR out (from the UWmic 9) into a traditional mixer-amplifier & then to a passive/active speaker with very good results. I think...
Reply

Re: Wireless Lavelier Mics & S1 Pro | Very Low Output!

Chet ·
I've found that I usually cannot get enough level from my dynamic microphones when plugged directly into the Bose S1 Pro (Shure SM58/Sennheiser 835). This tells me that the Pro doesn't provide the amount of input gain that most other systems do. That's another reason I use a mixer for gigging with my S1s (along with usually needing more than 2 input channels). An inline preamplifier designed for lavalier microphone use or inexpensive mixer may help you.
Reply

Re: wireless microphone

ST ·
Hi Marco, Thank you for joining the Community. What kind of microphone are you using now? Please say more about the "serious interferences" you are experiencing. I'd like to understand the problem better. Thank you, ST
Reply

Re: wireless microphone

Marco 4 ·
Hi for the time being I am practising with the "SAMSON CR77 UHF true Diversity Receiver together with the AH1 Samson (CH E3) Wireless microphone" -- a device used quite a lot in the Sport environment. To explain any choreography I'm using the microphone while the music is playing. So as the volume of the music is mostly to the upper level, when giving the instructions through the microphone, interferences appear(acoustical feedback). To avoid these biiiiiiiiiiip noise, the volume is to be...
Reply

Re: wireless microphone

ST ·
Hi Marco, From your description, you are experiencing acoustic feedback. Feedback occurs when the sound from the L1® Compact is louder at the microphone than the sound of the voice. This is shown in the diagram below. Note that in the diagram an L1 system is shown but the same fundamental fact is true for ANY loudspeaker. If you understand this diagram, it is relatively easy to understand how changes in an amplification system and the room can contribute to either increasing or decreasing...
Reply

Re: wireless microphone

Lee Wright ·
Hi Marco, I own Compacts & use sports headsets a bit for our outdoor events. What I would suggest it to locate the Compact off to the side so it's closer to your participants & further away from you. Perhaps angled at 45 degrees That type of headset is good in that it's a large diaphragm but the problem is that it's also a condenser type mic. For this sort of thing I normally go for a dynamic. The only one I know of is the Shure WH20. I have a couple & they work well. Fortunately...
Reply

Re: wireless microphone

Marco 4 ·
Thanks for this explanation and the drawings I have changed the position of the amplification system and it seems to work (no feedback occurred) thanks at lot marco
Reply

Re: wireless microphone

Marco 4 ·
Hi Lee thanks for your detailed explanation. I investigated on the Shure system, but it seems that it is not compatible with my Samson receiver system. Anyway I have changed the position of the L1 Compact and now it works thanks for your help
Reply

Re: wireless microphone

ST ·
Hi marco, Great news about the feedback solution. Thanks for coming back to tell us that you're okay. ST
Reply

Re: Wireless Mics

ST ·
Hi Shyam, Connections for wireless microphones are very similar to using wired microphones. Looking back at your previous posts, I see you have a T1®. That has four channels so you can connect up to four wireless microphone receivers. But you will probably want a least one channel for your backing tracks. So that leaves three. I would find most lavalier microphones are too prone to feedback to use for Karaoke or live performance situations. But handheld microphones are fine when used...
Reply

Re: Wireless Mics

Sam K ·
ST - Yes, that helps. Thanks so much! Shyam
Reply

Re: Correct Setup for DJs on the T8s

ST ·
Hi Cory, Congratulations! Please make sure you are running the latest firmware. See: T8S Firmware Updates Please tell us more about this connection. Do you have another mixer with RCA outputs? Please give us a link to the owner's manual. Consider using the USB to PC connection (find this under Prefs on the Rotary Selector). Please see: USB B from PC For both of these, please see: Gain Staging Use the Aux outputs. See: Aux Outputs For the F1 Model 812 systems see; T8S to F1 Model 812 Tip Ring...
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

Stephen ·
I would use a small mixer and feed everything into that and send an out from that to each Compact rather than daisy chain. You then have an Aux out on your mixer to feed whichever channels you want into your monitor, being in ear of floor monitor
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

Dr. J ·
Thank You Stephen - I thought about the Mixer route - will revisit that thought; thanks again.
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

DJ Erv ·
A music store suggested a bluetooth transmitter and earbuds for monitoring? Do their employees actually gig? We've tested it out and even with APTX bluetooth, you still get an unacceptable delay for monitoring live sound. Bluetooth is good for backing tracks. Good wireless In-Ear Monitors will cost you more than an S1 Pro. Cheaper would be get a small mixer and plug some wired in-ears into them. We mainly DJ but we also do a lot of sound reinforcement for conferences, schools, and occasional...
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

Jeff K ·
Our acoustic trio is left-right lead vox, cajon+vox, guitar+vox. We run a small Mackie ProFX mixer into two L1 Compacts (Mackie Left/Right XLR outputs to Left & Right L1 Compacts via Balanced 1/4" inputs, ToneMatch off). A couple of notes: The L1 Compact has near 180 degree coverage and are actually designed to be *behind* the performer, maybe off to the side a hair, so in your setup your mic may be to close to the sides of the L1's and causing the feedback. We've always had our L1's...
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

Dr. J ·
Thank You All for the suggestions; feedback etc. I will try the speaker placement as Jeff suggested failing that I'm sure a small mixer would also help.
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

Dr. J ·
Update: continued my research concluded the following re: Mixer the L1 Compact already has a pre-amp when using the XLR Mic Input with Treble and Bass Gain My Mic (Shure SM58) signal is coming from my TC-Halicon Harmony Singer (also has Gain and internal Tone) Will still receive a "Mono" sound if the L/R out from small mixer is directed to Each L1 Compact separately That all being said; a small mixer would still provide "some" control during performance (although I ONLY increase gain on the...
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

Dr. J ·
One other question - to Avoid Daisy Chain of the 2 L1 Compacts. I can connect the keyboard L & R to the 1/4 input to each of the 2 L1 Compacts I can connect the Phones Out of my Keyboard to the Instrument in of the TC Halicon Harmony singer Question: can i use a XLR Splitter from the TC Halicon XLR Out to go to Each XLR Li Compact's? The result would be L&R from Keyboard to each L1 Compact and TC Halicon XLR Split to each L1 Compact
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

Jeff K ·
Hi J, see my bulleted responses below: "Update: continued my research concluded the following re: Mixer" the L1 Compact already has a preamp when using the XLR Mic Input with Treble and Bass Gain Yes, this is true, but it's an overall EQ, nothing you can really use to dial out offending feedback frequencies. My Mic (Shure SM58) signal is coming from my TC-Helicon Harmony Singer (also has Gain and internal Tone) Yes, but again, not meant for feedback control. The mic output is also still mic...
Reply

Re: L1 Compact Output to Wireless/Bluetooth Ear Monitors

ST ·
Hi Dr J Wow - what a great discussion. You've been getting lots of great input. Your signal chain includes the Please try disabling the "Tone" feature. I have found it can work wonders or cause feedback. Most of the time, the latter. Cheers, ST
 
Post
Having trouble signing in?

We recently updated our sign-in procedure and if you have old sign-in data cached, this can create a problem. Please:

  1. Clear your browser cache and cookies
  2. Then close the browser (not just the window)
  3. Open the browser and try again
Thank you

Please make sure that your profile is up to date
×
×
×
×